Universidad de Cantabria-ko ikertzaileekin lankidetzan egindako argitalpenak (22)

2024

  1. Experimental Study on Styrene–Butadiene–Styrene-Modified Binders and Fly Ash Micro-Filler Contributions for Implementation in Porous Asphalt Mixes

    Sustainability (Switzerland), Vol. 16, Núm. 3

2023

  1. Rheological analyses of binders modified with triple combinations of Crumb-Rubber, Sasobit and Styrene-Butadiene-Styrene

    Case Studies in Construction Materials, Vol. 19

2022

  1. Step heating thermography supported by machine learning and simulation for internal defect size measurement in additive manufacturing

    Measurement: Journal of the International Measurement Confederation, Vol. 205

  2. UV curing study of semi-dense asphalt mixes with different sizes of copper slag – A sustainable rehabilitation and production strategy

    Construction and Building Materials, Vol. 347

  3. Use of Hydrated Ladle Furnace Slag as a filler substitute in asphalt mastics: Rheological analysis of filler/bitumen interaction

    Construction and Building Materials, Vol. 332

  4. Viscoelasticity modelling of asphalt mastics under permanent deformation through the use of fractional calculus

    Construction and Building Materials, Vol. 329

2021

  1. Mechanical performance of sustainable asphalt mixtures manufactured with copper slag and high percentages of reclaimed asphalt pavement

    Construction and Building Materials, Vol. 304

2020

  1. Influence of limestone filler on the rheological properties of bituminous mastics through susceptibility master curves

    Construction and Building Materials, Vol. 231

  2. Predictive models for the characterization of internal defects in additive materials from active thermography sequences supported by machine learning methods

    Sensors (Switzerland), Vol. 20, Núm. 14, pp. 1-26

  3. Study of the permanent deformation of binders and asphalt mixtures using rheological models of fractional viscoelasticity

    Construction and Building Materials, Vol. 260

2019

  1. Study of the mechanical behavior of asphalt mixtures using fractional rheology to model their viscoelasticity

    Construction and Building Materials, Vol. 200, pp. 124-134

  2. Use of plastic scrap in asphalt mixtures added by dry method as a partial substitute for bitumen

    Waste Management, Vol. 87, pp. 751-760

2018

  1. The use of copper slags as an aggregate replacement in asphalt mixes with RAP: Physical–chemical and mechanical behavioural analysis

    Construction and Building Materials, Vol. 190, pp. 427-438

  2. Thermal suspectability analysis of the reuse of fly ash from cellulose industry as contribution filler in bituminous mixtures

    Construction and Building Materials, Vol. 160, pp. 268-277

2017

  1. Reduction in the use of mineral aggregate by recycling cellulose ashes to decrease the aging of hot asphalt mixtures

    Construction and Building Materials, Vol. 143, pp. 547-557

2016

  1. Development of an estimative model for the optimal tack coat dosage based on aggregate gradation of hot mix asphalt pavements

    Construction and Building Materials, Vol. 118, pp. 1-10

  2. Effect of copper slag addition on mechanical behavior of asphalt mixes containing reclaimed asphalt pavement

    Construction and Building Materials, Vol. 119, pp. 268-276

2015

  1. Experimental study on stiffness development of asphalt mixture containing cement and Ca(OH)2 as contribution filler

    Materials and Design, Vol. 74, pp. 157-163

  2. Sustainability in construction works: Reuse of sludge from tunnel boring in lime mortars

    Applied Clay Science, Vol. 114, pp. 402-406

2013

  1. Experimental study of bituminous mastic behaviour using different fillers based on the UCL method

    Journal of Civil Engineering and Management, Vol. 19, Núm. 2, pp. 149-157